50mm PVC, uPVC or CPVC
Provide the plastic grade, dimensional standard, pressure class and actual OD. Furthermore, state the approved joining method.
Custom water stops for 50mm pipe penetrations
50mm Puddle Flange Manufacturer in India
Mesta Inc. manufactures 50mm puddle flanges for tank, drain, utility and concrete-wall penetrations. First, we verify the actual pipe OD and material; then, we follow the approved plate dimensions, assembly length and connection details.
50mm Puddle Flange for Tank, Drain and Wall Penetrations
A 50mm pipe can carry water, drainage, dosing chemicals or another project service through a concrete structure. However, the gap at the pipe-to-concrete interface can create a path for moisture when the design does not include a suitable water stop.
A 50mm puddle flange surrounds the pipe with a projecting plate. Consequently, water must follow a longer, obstructed route instead of tracking directly along the pipe surface. The product therefore supports watertight penetration details in tanks, walls, slabs, sumps and treatment structures.
Mesta Inc. supplies a separate puddle collar or a complete 50mm puddle flange pipe assembly. Depending on the project, the assembly can incorporate plastic or metallic pipe and suitable site-connection ends.
50mm size rangeSuitable for project-defined small service, drain, tank inlet and tank outlet penetrations.
50mm versus 2 inchWe verify the standard and actual OD because metric and nominal-inch descriptions may not match.
Material choicesBuyers can specify compatible plastic, mild steel, carbon steel or stainless steel construction.
Custom plate dimensionsThe approved penetration detail defines the plate OD, thickness and position.
50mm Puddle Flange Specifications
A complete specification must define more than the 50mm nominal description. In particular, the pipe standard controls the actual outside diameter and wall. Therefore, buyers should provide the following dimensional and material information.
| Size description | 50mm; purchaser to identify nominal size, nominal bore or actual outside diameter. |
|---|---|
| Inch reference | Often described commercially as 2 inch; nevertheless, the pipe standard and actual OD govern compatibility. |
| Pipe material | PVC, uPVC, CPVC, HDPE, mild steel, carbon steel, stainless steel or project-approved material. |
| Pipe wall | Pressure class, SDR, schedule or stated wall thickness as applicable. |
| Puddle plate OD | Total plate diameter or radial projection according to the approved waterproofing detail. |
| Plate thickness | Drawing-defined thickness that suits the material and attachment process. |
| Assembly length | Length based on concrete thickness, end projection and connection access. |
| Connection ends | Plain, socket, threaded, bevelled, spigot or flanged ends where suitable. |
| Surface protection | Compatible bare, painted, galvanized, passivated or project-specific finish. |
| Quality documents | Agreed material, dimensional, joint, coating and release records. |
50mm versus 2-inch: These terms do not always identify the same physical OD. Therefore, include the material, pipe standard and measured outside diameter in the enquiry.
50mm Pipe and Material Compatibility
The chosen pipe system determines the puddle flange bore, attachment method and available end connections. Consequently, each RFQ should identify the complete pipe designation.
50mm HDPE Pipe
Identify the PE grade and SDR because these details determine the pipe wall and fabrication requirements.
50mm MS or Carbon Steel
For a fabricated steel assembly, specify the grade, schedule, weld scope, coating and end preparation.
50mm Stainless Steel
For corrosive or hygienic service, define the stainless grade, wall, finish and required material records.
Compare our stainless steel puddle flanges, MS puddle flanges and PE puddle flanges.
Selecting a 50mm Water-Stop Plate
The plate must create the intended obstruction while leaving enough space for reinforcement and concrete. Therefore, coordinate these points on the approved detail:
- Actual pipe OD: size the component around the confirmed pipe rather than the commercial label.
- Radial projection: define the water-stop width that extends beyond the pipe surface.
- Plate thickness: select a value compatible with the material and fabrication method.
- Embedment location: show the plate position within the wall, slab or tank section.
- Concrete access: provide clearance for proper placement around both faces of the plate.
- External connection: preserve enough exposed pipe for sockets, threads, unions or flanges.
Application note: A puddle flange controls the path along the outside of the pipe. However, it does not replace the required pipe-joint, structural or complete waterproofing design.
50mm Puddle Flange Fabrication and Installation Process
A coordinated process protects the dimensional fit and water-stop location from workshop fabrication through concrete placement.
Confirm the Pipe System
First, verify the material, standard, actual OD, wall and required connection ends.
Review the Wall Detail
Next, confirm the concrete thickness, plate OD, thickness, position and assembly length.
Manufacture the Component
Then, prepare the pipe and plate and complete the approved material-compatible attachment.
Check Fit and Geometry
Inspect the bore, plate projection, alignment, ends and overall dimensions before dispatch.
Set and Support at Site
Afterwards, secure the assembly to the required line and level before concrete placement.
Complete Site Connections
Finally, inspect the exposed ends and make the specified pipe joints after the concrete work permits.
Quality Checks for a 50mm Puddle Flange
The inspection scope should confirm fit, geometry and attachment integrity. Accordingly, the order can include these checks and records.
Pipe Size Verification
Inspectors compare the stated standard and measured OD with the manufactured bore or pipe assembly.
Plate Dimensions
They verify the plate diameter, projection, thickness and location against the drawing.
Attachment Check
The team examines the welded, bonded, fabricated or mechanical attachment as specified.
Ends and Identification
Finally, inspectors check the connection ends, finish, marking and agreed documentation.
Applications of 50mm Puddle Flanges
The 50mm size supports many small water and utility penetrations. For example, project-specific uses may include:
- Water-tank inlet, outlet, drain and overflow connections
- Sump and collection-pit penetrations
- Small drainage lines through RCC walls or slabs
- STP, ETP and dosing-system pipe entries
- Pump-room auxiliary and service-water lines
- Basement-wall and foundation penetrations
- Industrial sampling, utility and wash-water services
Furthermore, buyers can review water-tank puddle flanges, drain puddle flanges and concrete-wall penetrations.
Details Required for a 50mm Puddle Flange Quote
For accurate sizing and pricing, provide the following information:
- Pipe material, dimensional standard and actual outside diameter
- Pressure class, SDR, schedule or wall thickness
- Service medium and project specification
- Concrete wall, slab or tank-wall thickness
- Required pipe or sleeve length
- Puddle plate OD or radial projection, thickness and location
- Approved plate attachment method
- Plain, socket, threaded, bevelled, spigot or flanged ends
- Inspection, coating, documentation and packing requirements
- Quantity, delivery location and drawing revision
50mm Puddle Flange Frequently Asked Questions
What is a 50mm puddle flange?
It is a water-stop collar or pipe assembly for a compatible 50mm-class penetration through concrete. Its projecting plate helps block water from tracking along the outside of the pipe.
Is a 50mm puddle flange the same as a 2-inch puddle flange?
Not always. Metric and nominal-inch pipe systems may use different actual outside diameters. Therefore, verify the pipe standard and OD before ordering.
Can you make a 50mm puddle flange for PVC pipe?
Yes, subject to design and fabrication review. Provide the PVC or uPVC standard, pressure class, measured OD and approved attachment method.
Can the assembly have threaded or socket ends?
Yes, when the pipe material, wall and project specification support the selected connection. Buyers should identify the exact thread or socket standard.
Can I use a 50mm puddle flange for a water-tank drain?
A project designer may specify it for a compatible 50mm tank drain. However, the drawing must define the pipe, water-stop plate, wall thickness and external connection.
Which plate dimensions should I provide?
Provide the total plate OD or projection, plate thickness and position. Additionally, include the concrete thickness and complete assembly length.
What information should I send for a quote?
Send the pipe standard, actual OD, wall, material, plate dimensions, assembly length, ends, quantity, inspection scope and drawing.
Request a 50mm Puddle Flange Quote
Send Mesta Inc. your pipe dimensions, puddle plate details, material, drawing, quantity, inspection scope and delivery requirements. Then, our team will review the enquiry and confirm the appropriate manufacturing scope.